Log Splitter Build Kit, 16 GPM Pump, 4" Cylinder, Auto-Ret Valve, Mount Coupler

ToolTuff Direct

$533.00 

4" Diameter Cylinder, High Pressure Line, 16 GPM Log Splitter Pump, Mount, Auto-Return Detent Valve and Coupler Kit w/Bolts/Fittings

From Tool Tuff Direct - Your Source for Log Splitter Parts Since 2012!

 

Build your own log splitter setup with this convenient kit!  Bolt this to your engine, and run some suction/discharge hoses and you're in business!  

Picture shows valve connected to cylinder - it is shipped separate, just screw in the included fittings with some thread tape and you'll be golden! 

 

INCLUDES: 

16 GPM 2 Stage Hydraulic Log Splitter Pump

 The 2-stage pump can give you faster cycle times and higher possible pressure with a small engine.  Excellent for use on log splitters.  85% efficient.

Suggested applications: Presses, Log Splitters, Clamping Units and Compactors

 

Specifications:

  • New Hydraulic Log Splitter Pump 16 GPM @ 3600RPM
  • Model # GP-CBN-160
  • Shaft: ½”
  • Inlet port: 1”
  • Outlet port: ½”
  • 7- 1/4" L with shaft
  • 5- 5/8” L without shaft
  • 3” across body
  • 3 -3/8” across mounting surface
  • Minimum 8 HP or larger gas engine, direct drive only, horizontal shaft (can be mounted vertical or horizontal)
  • For use with open center hydraulic systems only
  • First Stage: 13 GPM @ 650 PSI
  • Second Stage: 3 GPM @ 2500 PSI
  • Maximum pressure: 4000 PSI
  • Bolt circle: 2.83in.
  • 4 holes spaced 2” on center
  • Mounting hole diameter: .344in.
  • Woodruff key: 1/8in.
  • Rotation is clockwise
  • Flow rates on the hi-low tandem pumps are 0.256 cu in/rev on the low flow and 0.793 cu in/rev on the high flow pump.
  • This 2 stage pump can give you much faster cycle times and higher possible pressures with a small engine. Excellent for use on log splitters. 85% efficient.
  • Model GP-CBN is a HI/LO hydraulic gear pump with 12 different displacement combinations with maximum pressures of 900 psi for the low pressure pump and 3000 psi for the high pressure. The change from LO to HI pressure is automatic with the LO side pressure pre set from 400 psi to 900 psi.
  • The HI/LO section of the pump is all aluminum and the end plates are cast steel. Applications for the HI/LO pump are log splitters, presses etc where rapid movement of the cylinder at low pressure is required prior to automatically switching to the high pressure mode to meet load requirements.

Lovejoy LO90 Coupler 

This kit includes two coupler halves and one rubber spider. The default set is L090 1/2" and 1". Please message us if you need a different size. You can choose from L090 3/4" 5/8" 7/8" 1" or 1-1/8"

A7 Auto-Return Log Splitter Valve  

(We have other valves available - if the schematic looks different than your valve, message us and we can substitute it)

Valve Specs:

Single spool, Open center.

  • Max pressure rating: 3500psi.
  • Relief valve set at 3100psi but is adjustable.
  • Working ports ½”NPT.
  • In/Out ports ¾” NPT
  • Detent Pressure set at 700 psi but is adjustable.
  • Compatible with most splitters (SpeeCo, MTD, Brave, Swisher etc)
  • Threaded end cap for easy detent adjustment

 

Mounting bracket holes (4) are 5/16-18 thread pitch and are spaced 1" x 2-5/8" apart

This is the next generation in log splitter valves. The detent is usually what wears out and causes valves to fail. This valve allows user to adjust the kick out pressure to what they need and as detent balls and grooves wear.

Pump to Mount Bolts, Lock Washers, Nuts

  • Includes the required bolts, nuts and lock washers required to mount the pump to the mount.  You'll supply your own engine mounting bolts.  

 

Log Splitter Valve, Adjustable Detent.

 

Single spool, Open center.

  • Max pressure rating: 3500psi.
  • Relief valve set at 3000psi but is adjustable.
  • Working ports ½”NPT.
  • In/Out ports ¾” NPT
  • Detent Pressure set at 700 psi but is adjustable.
  • Compatible with most splitters (SpeeCo, MTD, Brave, Swisher etc)
  • Screw off end cap for easily detent pressure adjustability

4" Bore x 24" Stroke Hydraulic Log Splitter Cylinder (OEM Replacement for TSC, Huskee,SplitMaster, Oregon, SpeeCo, Etc)

In addition to being great "build it yourself splitter" parts, our cylinders will replace your original worn-out double acting TSC, Huskee, SplitMaster, Oregon, SpeeCo and many other Log Splitter cylinders that have the double-ear mounting clevis as shown in our pictures without any modifications needed. Most of the time they are direct-fit.  All fit-up dimensions are listed in the picture section of this add.

Quick Specifications:

  • All welded design
  • Direct replacement for TSC Huskee, SplitMaster, Oregon, SpeeCo and many others
  • USA seller
  • Double acting
  • Rebuildable (seals can be replaced)
  • 1-3/4" Chrome rod with 9/16" mounting hole for wedge mounting
  • Double mounting clevis design to accept 1-1/8" pin mounted at the front of the log splitter beam
  • 24" stroke
  • 4" diameter bore
  • 1/2" NPT hydraulic ports
  • 3500 maximum operating pressure
  • Painted black
  • 1-1/8" Clevis mounting holes
  • Ships via UPS ground to the lower 48 states only!!!
  • This cylinder used with any 2 stage gear pump (Common are 11gpm, 13gpm and 16gpm)  will provide approximately 22 tons of splitting force

Pump Mount for hydraulic log splitter, 8hp-15hp. Speeco, Brave, Northern wood

 

Pump Mount for Log Splitters and other equipment. Direct replacement for SpeeCo, Splitmaster, Oregon, Husky 28, 33, 34 and 35t units. 

  • Length: 5-1/4"
  • Pump Bolt Circle: 2-3/4", or 2" square. Holes tapped for 5/16" bolt
  • Engine Bolt Circle: 5" or 3-1/2" square.
  • Cast Iron construction.
  • Works with Halidex, MTD, Deli and other 11 gpm - 16 gpm pumps.
  • Mounts to Briggs, Honda, Kohler, Subaru 8-15 hp motors

Cylinder 4" Bore x 24" Stroke

  • All welded design
  • Direct replacement for TSC Huskee, SplitMaster, Oregon, SpeeCo and many others
  • USA seller
  • Double acting
  • Rebuildable (seals can be replaced)
  • 1-3/4" Chrome rod with 9/16" mounting hole for wedge mounting
  • Double mounting clevis design to accept 1-1/8" pin mounted at the front of the log splitter beam
  • 24" stroke
  • 4" diameter bore
  • 1/2" NPT hydraulic ports
  • 3500 maximum operating pressure
  • Painted black
  • 1-1/8" Clevis mounting holes
  • Ships via UPS ground to the lower 48 states only!!!
  • This cylinder used with any 2 stage gear pump (Common are 11gpm, 13gpm and 16gpm)  will provide approximately 22 tons of splitting force

Check Out Our Brands!